+86-373-8729999

SBD-C Hydraulic Safety Disc Brake · FAQ

Nov 05, 2026

 

1. Product Positioning

The SBD-C series is a normally-closed, spring-applied, hydraulically-released fail-safe disc brake​ for low-speed shafts / drum shafts.

It is designed for:

Emergency safety braking

Holding / parking brake

Backup braking under power loss, oil loss, or system fault

It is not​ intended as a high-frequency service brake.

2. Working Principle

Disc springs apply braking force; hydraulic pressure releases the brake.

Condition

Hydraulic Pressure

Disc Spring

Brake Arms

Result

Normal / power loss

No pressure

Released elastic force

Clamp disc

Brake engaged

Running / released

Pressure supplied

Compressed

Open & retract

Brake released

Logic:

Hydraulic oil enters cylinder → piston compresses disc springs

Brake arms open → linings separate from disc

Power/off pressure lost → springs push pistons back

Linings clamp the disc → braking torque holds the shaft

This is a fail-safe​ design: braking does not depend on electricity.

3. Typical Parameters (Reference)

Assumed friction coefficient μ = 0.35; disc diameter D ≥ 1800 mm.

Model

Rated Clamping Force (kN)

Braking Force (kN)

Operating Pressure (MPa)

Single-side Gap (mm)

Release Oil Vol. (mL)

SBD250-C

250

180

8

1–2

275

SBD365-C

365

262

8

1–2

275

SBD425-C

425

306

9.5

1–2

275

Braking torque estimate:

T ≈ μ × F × d₁

μ = 0.35

F = total clamping force (kN)

d₁ = effective friction diameter ≈ D − 220 (mm)

T in N·m

4. Main Applications

Overhead / gantry / portal cranes: hoisting and luffing low-speed shafts

Mine hoists, winches, elevators

Inclined belt conveyors

Cable cars, ropeway drives

Foundry cranes and other heavy-duty lifting equipment

5. Key Features

Normally closed, fail-safe operation

High clamping force, short closing time

Stable non-asbestos linings, insensitive to water/salt spray

Optional switches: release limit, lining wear limit, closed position

Good heat dissipation vs. drum brakes

PLC-interlock ready

FAQ

Q1. Can SBD-C be used on high-speed shafts?​

Not recommended. It is for low-speed/high-torque shafts. High-speed use causes excessive heat and lining wear.

Q2. How often should linings be inspected?​

Visually every shift; measure thickness weekly. Replace when lining material reaches the manufacturer's minimum, commonly around 3 mm remaining friction material.

Q3. What hydraulic station is required?​

Pressure per nameplate, usually 8–9.5 MPa, with accumulator, pressure switch, and fail-safe relief logic. Use anti-wear hydraulic oil with proper cleanliness.

Q4. Why does one lining wear faster?​

Usually stuck guide pin, unequal air gap, or disc runout. Clean slides and re-adjust symmetry.

Q5. Is the brake suitable for frequent cycling?​

No. SBD-C is a safety/holding brake. For frequent dynamic braking, add a service brake or variable-frequency control.

Q6. What switches can be added?​

Release limit switch (RL), lining wear limit switch (WL), closed-position switch (Cl). All can feed PLC interlocks.

Q7. What if the disc gets oily?​

Stop, clean disc and linings with suitable solvent, then find and repair the leak. Oil drastically reduces friction.

Q8. Does it work during power failure?​

Yes. That is the core function: loss of power/pressure automatically applies the brake.

Q9. Can it be used in explosive atmospheres?​

Standard units are not inherently explosion-proof. Use certified explosion-proof hydraulic and electrical components for such sites.

Q10. After lining replacement, is running-in needed?​

Yes. No-load cycles first, then incremental load. Verify contact pattern and re-check gap.

 

Send Inquiry